Skil 1743 AE Instruction Manual download pdf (Page 10)

• Selecting operating mode 9

- press button F to unlock switch E

- turn switch E to the desired operating mode until it

snap-locks

! startworkingonlywhenswitchEislocked

1 = normal drilling/screwdriving

2 = impact drilling

3 = chiseling

! selectoperatingmodeonlywhentoolisswitched

offandplugisdisconnected

- for drilling in wood, metal and plastic as well as for

screwdriving the corresponding adapter should be

used (see: Application Advice)

- the hammer mechanism is activated by applying a

slight pressure on the tool when the drill bit is in

contact with the workpiece

- best impact drilling results can be obtained by only a

slight pressure on the tool needed to keep the

automatic clutch engaged; drilling performance will not

improve by applying more pressure on the tool

• Chiseling with rotating chisel

! switchoffthetoolanddisconnecttheplug

- select “rotating” chiseling mode

• Chiseling with xed chisel

! switchoffthetoolanddisconnecttheplug

- select “rotating” chiseling mode

- place chisel in desired position

- select “xed” chiseling mode

• Changing bits 0

! cleanandlightlylubricatetheSDS+accessory

beforeinsertion

- pull back locking sleeve G and insert accessory in

SDS+ chuck while turning and pushing it until it

engages; the accessory locks in position automatically

- pull accessory to check that it is locked correctly

- remove accessory by pulling back locking sleeve G

! theSDS+accessoryrequiresfreedomof

movementwhichcauseseccentricitywhentoolis

off-load;however,theaccessoryautomatically

centresitselfduringoperationwithoutaffecting

drillingprecision

! donotusebits/chiselswithadamagedshank

• Safety clutch

If the accessory gets jammed, the drive to the spindle is

interrupted (causing a rattling noise)

- immediately switch o tool

- remove the jammed accessory

- switch on tool again

• Adjusting drilling depth !

• Holding and guiding the tool @

! whileworking,alwaysholdthetoolatthe

grey-colouredgriparea(s)

- alwaysuseauxiliaryhandleH (can be adjusted as

illustrated)

- keep the ventilation slots uncovered

- do not apply too much pressure on the tool; let the tool

do the work for you

APPLICATIONADVICE

• Use the appropriate bits #

! onlyusesharpbits/chisels

• For drilling in wood, metal and plastic as well as for

screwdriving use the corresponding adapter (SKIL

accessory 2610395660) $

- clean and lightly lubricate adapter before insertion

- pull back locking sleeve G 2 and insert adapter in

SDS+ chuck while turning and pushing it until it

engages; the adapter locks in position automatically

- pull adapter to check whether is it locked correctly

- set switch E 2 to normal drilling (onlyactivatewhen

toolisswitchedoffandplugisdisconnected)

• When drilling ferrous metals

- pre-drill a smaller hole, when a large hole is required

- lubricate drill bit occasionally with oil

• When turning in a screw at/near the cross cut end or an

edge of wood, pre-drill a hole in order to avoid cracking of

the wood

• Splinterfree drilling in wood %

• Dustfree drilling in walls ^

• Dustfree drilling in ceilings &

• Drilling in tiles without skidding *

• For more tips see www.skileurope.com

MAINTENANCE/SERVICE

• Always keep tool and cord clean (especially ventilation

slots J 2)

! disconnecttheplugbeforecleaning

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of

the tool are listed on www.skileurope.com)

ENVIRONMENT

• Donotdisposeofelectrictools,accessoriesand

packagingtogetherwithhouseholdwastematerial

(only for EU countries)

- in observance of European Directive 2002/96/EC on

waste of electric and electronic equipment and its

implementation in accordance with national law,

electric tools that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility

- symbol ( will remind you of this when the need for

disposing occurs

DECLARATIONOFCONFORMITY

• We declare under our sole responsibility that this product

is in conformity with the following standards or

standardized documents: EN 60745, EN 61000,

EN 55014, in accordance with the provisions of the

directives 2004/108/EC, 2006/42/EC

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 119 120

Comments to this Manuals

No comments

Skil 1743 AE Instruction Manual Page 10

Comments to this Manuals

Related products and manuals for Rotary hammers Skil 1743 AE