IMPORTANT: IMPORTANT : IMPORTANTE:Read Before Using Lire avant usage Leer antes de usarOperating/Safety InstructionsConsignes de fonctionnement/sécuri
-10-RIP FENCE AND CIRCLE CUTTING GUIDEThis accessory is available at an extra cost. Itis used for fast and accurate straight andcircle cutting (Fig. 1
-11-STRAIGHT CUTTINGOnce the rip fence is attached, measure fromthe edge of work to the line of cut, and set edgeguide of rip fence to the same distan
-12-ServicePreventive maintenanceperformed by unauth-orized personnel may result in misplacingof internal wires and components whichcould cause seriou
-13-Veuillez lire et comprendre toutes les consignes. Si on n'observe pas toutes lesconsignes décrites ci-dessous, il y a risque de choc électri
-14-Tenez l'outil par les surfaces isolées de préhensionen exécutant une opération au cours de laquellel'outil de coupe peut venir en contac
-15-Évitez de vous placer les mains entre le carterd'engrenages et le porte-lame de la scie. Le porte-lame à mouvement alternatif risquerait de v
-16-SymbolesIMPORTANT : Certains des symboles suivants peuvent être utilisés sur votre outil. Veuillez les étudier etapprendre leur signification. Une
-17-Description fonctionnelle et spécificationsDébranchez la fiche de la prise de courant avant d'effectuer quelque assemblageou réglage que ce s
-18-Pose de la lamePour éviter le risque de bles-sure, débranchez toujours lecordon de la source d’alimentation avant d’effectuer lesréparations et ré
-19-ÉCLAIRAGE D’APPOINT INTÉGRÉVotre outil est également doté d’une lampe qui s’allumeautomatiquement quand on appuie sur la gâchette pouraméliorer la
-2-Work area safetyKeep work area clean and well lit.Cluttered or dark areas invite accidents.Do not operate power tools in explosiveatmospheres, such
-20-COUPE EN PLONGÉELa coupe en plongée est utile et pratique pour pratiquerdes ouvertures grossières dans les matériaux plusmous. Il n’est pas nécess
-21-COUPE DANS LES MÉTAUXPrenez bien soin d’assujettir le matériau avec des serres.De même, déplacez la scie lentement. Choisissez lesvitesses lentes.
-22-COUPE CIRCULAIRE1. Avant d’attacher le guide de refente, tracez un cercle etenfoncez un clou de finition en son centre.2. Percez un trou ou faites
-23-ServiceTout entretien préventifeffectué par despersonnels non autorisés peut résulter en mauvaisplacement de fils internes ou de pièces, ce qui pe
-24-Lea todas las instrucciones. Si no se siguen todas las instrucciones que aparecen acontinuación, el resultado podría ser sacudidas eléctricas, inc
-25-Normas de seguridad para sierras de caladoraSujete la herramienta por las superficies de agarreaisladas cuando realice una operación en la que lah
-26-Mantenga las manos alejadas del área de corte.No ponga la mano debajo del material que se estácortando. La proximidad de la hoja a la mano quedao
-27-SímbolosIMPORTANTE: Es posible que algunos de los símbolos siguientes se usen en su herramienta. Por favor,estúdielos y aprenda su significado.
-28-Descripción funcional y especificacionesDesconecte el enchufe de la fuente de energía antes de realizar cualquier ensamblajeo ajuste, o cambiar ac
-29-EnsamblajeINTERRUPTOR GATILLO “ON/OFF” (DE ENCENDIDO Y APAGADO)Para encender la herramienta (posición “ON”), apriete elinterruptor gatillo. Para a
-3-Safety Rules for JigsawsHold tool by insulated gripping surfaceswhen performing an operation where thecutting tool may contact hidden wiring orits
-30-ACCIÓN ORBITALLa palanca de acción orbital (Fig. 7) regulará la acciónorbital desde la posición "Smooth" ("suave") paramovimie
-31-Consejos para cortarColoque el lado bueno del material hacia abajo y fíjelo enun tornillo de carpintero de banco o sujételo conabrazaderas. Trace
-32-CORTE INCLINADO O EN ÁNGULODesconecte el cordón de la fuente de energía. La base sepuede ajustar para cortar ángulos a 0° ó 45° encualquiera de l
-33-CORTE CIRCULAR1. Antes de colocar el tope-guía para cortar al hilo, traceun círculo y clave un clavo fino en el centro del círculo.2. Perfore un c
-34-AccesoriosSi es necesario un cordón deextensión, se debe usar uncordón con conductores de tamaño adecuado que seacapaz de transportar la corriente
-35-Notes:Remarques :Notas:SM 1619X00459 1-05 12/8/04 9:19 PM Page 35
1619X00459 01/05 Printed in ChinaLIMITED WARRANTY OF SKIL CONSUMER PORTABLE POWER TOOLS FOR HOME USERobert Bosch Tool Corporation (“Seller”) warrants
-4-Keep hands away from cutting area. Donot reach under the material being cut.The proximity of the blade to your hand ishidden from your sight.Keep
-5-IMPORTANT: Some of the following symbols may be used on your tool. Please study themand learn their meaning. Proper interpretation of these symbo
-6-Functional Description and SpecificationsDisconnect the plug from the power source before making anyassembly, adjustments or changing accessories.
Attaching the BladeTo prevent personal injury,always disconnect plug frompower source before assembling parts, makingadjustments, or changing blades.
DUST EXTRACTIONYour jigsaw is equipped with a dust port fordust and chip extraction.To use this feature, remove blade storagecompartment and move dust
-9-Cutting TipsFace the good side of the material down andsecure it in a bench vise or clamp it down.Draw cutting lines or designs on the side ofthe m
Comments to this Manuals