Skil 2770 AA Instruction Manual download pdf (Page 8)

7 Do not dispose of the battery together with

household waste material

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

•

Do not connect the blue (= neutral) or br

own (= live) wire

in the cord of the charger to the earth terminal of the

plug

• If for any r

eason the old plug is cut off the cord of the

charger, it must be disposed of safely and not left

unattended

USE

• On/Off 8

• Speed control for smooth starting 9

• Char

ging battery 2

! a lithium-ion battery that is new or has not been

used for a longer period does not develop its full

capacity until after approximately 3

charging/

discharging cycles

- plug char

ger into power source

- light C will turn on GREEN indicating that the charger

is ready for operation

- insert tool into char

ger

- light C/K will turn RED indicating that the battery is

being charged

- after 3

hours the battery is fully charged and charging

automatically stops (indicator K turns off)

- if the tool is used only brieﬂy

, the charging time can

be very short

- unplug the char

ger when the battery is fully charged

IMPORTANT:

- if light C does not turn RED after inserting tool into

charger, this may mean that the battery is too cold or

too hot; when the battery temperature returns to

between 0°C and 45°C, the charger will automatically

begin charging

the lithium-ion battery can be charged at any time

(interrupting the charging procedure does not

damage the battery)

- while char

ging, the charger and the battery may

become warm to touch; this is normal and does not

indicate a problem

- do not char

ge at temperatures below 0°C and over

45°C; this will seriously damage the battery as well

as the charger

- when the lithium-ion battery is empty

, the tool is

switched off automatically

! do not continue to press the on/off switch after

the tool is switched off automatically; battery may

be damaged

• Changing dir

ection of rotation 0

- indicator E shows the selected dir

ection of rotation

- when not properly set in left/right position, switch

A 2 cannot be activated

! change direction of rotation only when tool is at a

complete standstill

• Changing bits !

- insert the bit as deep as possible in the chuck

do not use bits with a damaged shank

! only use sharp bits

• Torque control (VariTorque)

- output tor

que will increase as clutch ring G is rotated

from 1 to 7; position H will lock up the clutch to

permit drilling or driving heavy duty work

- when tur

ning in a screw, ﬁrst try VariTorque position 1

and increase until the desired depth has been

reached

• Mechanical gear selection #

- set selector J to desir

ed speed

! actuate the gear selector while tool is running

slowly

HIGH POWER

- high tor

que

- for screwdriving and drilling large diameters

- for tapping thread

HIGH SPEED

- lower tor

que

- for drilling small diameters

• Low battery level indicator

When battery level is low, indicator K lights on

•

Mounting charger on the wall

• Holding and guiding the tool

while working, always hold the tool at the grey-

coloured grip area(s) ^

- keep ventilation slots L 2

uncovered

- do not apply too much pr

essure on the tool; let the

tool do the work for you

APPLICATION ADVICE

• When drilling ferrous metals

- pre-drill a smaller hole, when a large hole is required

- lubricate drill bit occasionally with oil

• When turning in a screw at/near the cross cut end or an

edge of wood, pre-drill a hole in order to avoid cracking

of the wood

• For an optimal use of the tool a steady pr

essure on the

screw is required, especially while removing

• When scr

ewdriving in hard wood one should pre-drill a

hole

MAINTENANCE / SERVICE

• Keep tool and charger clean

! unplug charger from power source before

cleaning

- clean char

ging contacts in charger with alcohol or

contact cleaner

• If the tool/char

ger should fail despite the care taken in

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

- send the tool or char

ger undismantled together with

proof of purchase to your dealer or the nearest SKIL

service station (addresses as well as the service

diagram of the tool are listed on

www.skileurope.com)

ENVIRONMENT

• Do not dispose of electric tools, accessories and

packaging together with household waste material

(only for EU countries)

SKIL_IB2770v2_EU.indd 8 04-05-2010 14:00:14

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 119 120

Comments to this Manuals

No comments

Skil 2770 AA Instruction Manual Page 8

Comments to this Manuals

Related products and manuals for Cordless combi drills Skil 2770 AA