Skil 4900 AK Instruction Manual download pdf (Page 9)

- connect plug to power source (light B turns on

indicating that the tool is receiving power) !

- hold the tool with one hand on handle G 2 and the

other on the insulated barrel grip H 2

- switch on the tool

! the tool should run at full speed before the blade

enters the workpiece

- guide the tool along the marked cutting line

- keep footplate E 2 rmly against the workpiece to

minimize counter-force and vibration

• Holding and guiding the tool

! while working, always hold the tool at the

grey-coloured grip area(s) @

- keep ventilation slots J 2 uncovered

- do not apply too much pressure on the tool; let the tool

do the work for you

! ensure that the saw blade extends beyond the

work throughout the stroke #

• Adjusting eective stroke length $

- use both adjustment screws K for sliding footplate E

forward/backwards in order to enlarge/reduce the

eective stroke length

! do not attempt to adjust the effective stroke length

with screw L which is pre-set at manufacturing

APPLICATION ADVICE

• Plunge cutting %

Plunge cuts can be made in wood and other soft

materials without pre-drilling a hole

- use a thick saw blade

- mount the blade with the teeth facing upward

- hold the saw upside down as illustrated

- mark desired cutting line on the workpiece

- select position 1, 2 or 3 with wheel C

- tilt the tool so that the blade does not touch

the workpiece

- switch on the tool and carefully engage the moving

saw blade into the workpiece

- after the blade has penetrated through the workpiece

continue sawing along the marked cutting line

! do not make plunge cuts in metal materials

• Use the appropriate saw blades ^

• When cutting metals, lubricate saw blade regularly with oil

• Splinter-free cutting

- cover cutting-line with several layers of wide tape

before cutting

- always face the good side of the workpiece down

• For more tips see www.skil.com

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Always keep tool and cord clean (especially ventilation

slots J 2)

! disconnect the plug before cleaning

• If the tool should fail despite the care taken in manufacturing

and testing procedures, repair should be carried out by an

after-sales service centre for SKIL power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of

the tool are listed on www.skil.com)

ENVIRONMENT

• Do not dispose of electric tools, accessories and

packaging together with household waste material

(only for EU countries)

- in observance of European Directive 2012/19/EC on

waste of electric and electronic equipment and its

implementation in accordance with national law,

electric tools that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility

- symbol & will remind you of this when the need for

disposing occurs

DECLARATION OF CONFORMITY

• We declare under our sole responsibility that this product

is in conformity with the following standards or

standardized documents: EN 60745, EN 61000, EN

55014, in accordance with the provisions of the directives

2004/108/EC, 2006/42/EC, 2011/65/EU

• Technical file at: SKIL Europe BV (PT-SEU/ENG1),

4825 BD Breda, NL

¹ÊÁÂÆÎ¹Æ¼½ÊÇÇ¾¼½Æ

È½Ê¹ÌÁÇÆËŵÆ¿ÁÆ½½ÊÁÆ¿

ÍÊÇÈ½Ɠˁ˅ʿ˂Ê½¼¹Ɠ

Ä¹¾ÁÂÃ¿Ê¹¹¾

ÈÈÊÇÎ¹Ä¹Æ¹¿½Ê

09.12.2013

NOISE/VIBRATION

• Measured in accordance with EN 60745 the sound

pressure level of this tool is 90 dB(A) and the sound

power level 101 dB(A) (standard deviation: 3 dB), and the

vibration ✱ (hand-arm method; uncertainty K = 1.5 m/s²)

✱ when cutting chipboard 12.1 m/s²

✱ when cutting wooden beams 12.2 m/s²

• The vibration emission level has been measured in

accordance with a standardised test given in EN 60745; it

may be used to compare one tool with another and as a

preliminary assessment of exposure to vibration when

using the tool for the applications mentioned

- using the tool for dierent applications, or with dierent

or poorly maintainted accessories, may signicantly

increase the exposure level

- the times when the tool is switched o or when it is

running but not actually doing the job, may signicantly

reduce the exposure level

! protect yourself against the effects of vibration

by maintaining the tool and its accessories,

keeping your hands warm, and organizing your

work patterns

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 115 116

Comments to this Manuals

No comments

Skil 4900 AK Instruction Manual Page 9

Comments to this Manuals

Related products and manuals for Sabre saws Skil 4900 AK